Gel Coat Restoration

dpg · 05-12-2005, 05:39 AM

Hello - This morning I ordered a Gel Coat restoration system on line. I was wondering if anyone has used these products before and what your results were. Hey, for $70.00 even if it does half of what it claims it'll be an improvement!

It happens to be called Vertglas Restoration System.

Silver Duck · 05-12-2005, 06:56 PM

DPG

From what I've heard, if you follow the directions "to the letter" the results can be fantastic.

However, I've also heard that when it needs to be re-done the old stuff needs to be stripped before another treatment can be applied, and that this is a real PITA to do.

Silver Duck

dpg · 05-16-2005, 05:44 AM

Ya, I guess I never thought of stripping it. Not sure but I believe the stuff just kind of "wears off" don't really know. The company does sell a stripper on their site now that I think of it. Oh well, looks terrible I'm going for it.

BroadHopper · 05-16-2005, 11:20 AM

Let's face it. When the gelcoat is gone it's gone. All the boat magazines says there is now way to permanently repair faded gelcoat other than to paint over or replace it.
As for temporary restoration, 3M gelcoat cleaner and wax gets my vote. There is a heavy duty one for extreme oxidation as well as a medium. Unfortunately the wax only last about a month. I apply the Bright Star with teflon over the initial treatment. That will make it last the season. The teflon makes it a snap to keep clean.
A trick I learn is to dilute the 3M product in a bucket of water and 'paint' the effected area with a paint brush with it. Then use the buffer. This is a lot easier.

Excalibur · 05-16-2005, 11:28 AM

Hey that sounds like a great short cut. What is the ratio you use to dilute the 3M compound. Also do you use a regular orbital car buffer? Thanks for the insite.

BroadHopper · 05-16-2005, 11:48 AM

I just dilute it enough so that I can spread it with a paint brush.
I use a regular car orbital buffer. But make sure you use a 'cutting' pad rather than the normal buffing pad. If the cutting pad gets clogged I just run a screwdriver through the pad and 'fluff it' up.
Good luck in your detailing.

BTW. Did anyone use 'Australian Timber oil' by Cabot Stain on teak platforms and decks? I like to try it but need opinons.

05-12-2005, 05:39 AM	#1
dpg Senior Member Join Date: Apr 2004 Posts: 2,591 Thanks: 150 Thanked 229 Times in 166 Posts	Gel Coat Restoration Hello - This morning I ordered a Gel Coat restoration system on line. I was wondering if anyone has used these products before and what your results were. Hey, for $70.00 even if it does half of what it claims it'll be an improvement! It happens to be called Vertglas Restoration System.

05-16-2005, 11:20 AM	#4
BroadHopper Senior Member Join Date: Oct 2004 Location: Laconia NH Posts: 5,569 Thanks: 3,202 Thanked 1,101 Times in 793 Posts	Gelcoat repair Let's face it. When the gelcoat is gone it's gone. All the boat magazines says there is now way to permanently repair faded gelcoat other than to paint over or replace it. As for temporary restoration, 3M gelcoat cleaner and wax gets my vote. There is a heavy duty one for extreme oxidation as well as a medium. Unfortunately the wax only last about a month. I apply the Bright Star with teflon over the initial treatment. That will make it last the season. The teflon makes it a snap to keep clean. A trick I learn is to dilute the 3M product in a bucket of water and 'paint' the effected area with a paint brush with it. Then use the buffer. This is a lot easier. __________________ Someday may never be an actual day.

05-16-2005, 11:48 AM	#6
BroadHopper Senior Member Join Date: Oct 2004 Location: Laconia NH Posts: 5,569 Thanks: 3,202 Thanked 1,101 Times in 793 Posts	Shortcut I just dilute it enough so that I can spread it with a paint brush. I use a regular car orbital buffer. But make sure you use a 'cutting' pad rather than the normal buffing pad. If the cutting pad gets clogged I just run a screwdriver through the pad and 'fluff it' up. Good luck in your detailing. BTW. Did anyone use 'Australian Timber oil' by Cabot Stain on teak platforms and decks? I like to try it but need opinons. __________________ Someday may never be an actual day.

05-12-2005, 06:56 PM	#2
Silver Duck Senior Member Join Date: Apr 2004 Location: Billerica, MA Posts: 364 Thanks: 40 Thanked 4 Times in 3 Posts	DPG From what I've heard, if you follow the directions "to the letter" the results can be fantastic. However, I've also heard that when it needs to be re-done the old stuff needs to be stripped before another treatment can be applied, and that this is a real PITA to do. Silver Duck

05-16-2005, 05:44 AM	#3
dpg Senior Member Join Date: Apr 2004 Posts: 2,591 Thanks: 150 Thanked 229 Times in 166 Posts	Ya, I guess I never thought of stripping it. Not sure but I believe the stuff just kind of "wears off" don't really know. The company does sell a stripper on their site now that I think of it. Oh well, looks terrible I'm going for it.

05-16-2005, 11:28 AM	#5
Excalibur Senior Member Join Date: Jul 2004 Location: Gilford,NH is where I would like to be and Southborough, MA is where I have to be Posts: 88 Thanks: 14 Thanked 10 Times in 3 Posts	Hey that sounds like a great short cut. What is the ratio you use to dilute the 3M compound. Also do you use a regular orbital car buffer? Thanks for the insite.