Boat Whips vs Boat Lift

Misty Blue · 05-17-2012, 05:22 PM

A way to deal with this is to use a kedgeing anchor.

A kedge is an anchor (either a regular anchor or a mooring block) attached to the outboard side of the boat.

Our set up... About 15 feet outboard of our boats we plant a mooring block. Attached to the block is about 6 feet of heavy chain. Attached to the chain is enough nylon (1/2 inch is good) line to reach a conveniant place on your dock.

You tie up the boat to the dock in the regular way only a bit looser. You then take the kedging line and secure it to your outboard, midships cleat. With the loose dock lines the kedging line will pull the boat away from the dock. Adjust your docking lines so that the boat is about a foot from the rubbing posts. The weight of the chain running along the bottom will lift and drop as the boat moves up and down and will act as a shock absorber. It is cheap and easy on the boat and no permit required.

Good luck!

Misty Blue.

Rattlesnake Guy · 05-17-2012, 07:59 PM

We have used the same pair of over sized whips on the broads for 10 years. We have always used the collapsing triangle method as shown here. The triangle prevents the twisting force.

Jonas Pilot · 05-17-2012, 08:34 PM

Do you use bumpers too?

Rattlesnake Gal · 05-18-2012, 08:13 AM

Quote:

Originally Posted by Jonas Pilot

Do you use bumpers too?

Only one in the very front because when the wind and wave are exactly right, the boat can kiss the dock. If it is that rough, we tie a line to shore to keep that from happening.

SAMIAM · 05-18-2012, 08:38 AM

I've had great luck with mooring whips....secret is...go oversize for your boat or make sure they are heavy duty and they should handle most anything. Misty Blue has a good idea too. If you place a well anchored mooring ball for the bow, you can tie the stern to your dock and still have easy access to your boat. Not too difficult, just takes a little experimenting.
Boat lifts are fine in salt water since you need to wash your boat and flush your engine after use but for fresh water, that's a lot of money to spend when there are lots of cheaper options. Good luck.

Flyfisha · 05-18-2012, 09:45 AM

Done it both ways--I have had oversize whips for about 15 years and have had good luck. My shore station sits on Rattlesnake looking for a new home. Sorry it's only rated for 3600#

It really became a pain to take out and put in!

Rangervx · 05-18-2012, 11:47 AM

i would suggest contacting the folks at Mooring Products International. they are the inventors of the mooring whips and their whips are top notch. i would never trust my boat to anything other than these whips...period...end of story. they are out of florida...call them up and don't be suprised if you speak with the owner/president.

Rattlesnake Guy · 05-18-2012, 10:05 PM

RG has become an expert at tying lines to the dock post in a way that the lines do not wear from rubbing. Probably common to many on here but she wraps it so the line exist from between two other wraps and can't rub on the wood.

Kamper · 05-20-2012, 07:56 AM

Quote:

Originally Posted by Misty Blue

A way to deal with this is to use a kedgeing anchor. ... It is cheap and easy on the boat and no permit required.

Good luck!

Misty Blue.

Another term for this is off-set mooring and I've used the technique with great results too, and recomended it on a couple threads. However... One of our members tried it, and when going out for a cruise tossed the line back into the water. One day there was an MP nearby who cited him for unlicensed mooring. After reading that I was careful to look around when I launched. If there was an MP nearby I pulled the rig from the water before heading out.

My rig was set up with chain to the anchor and a loop of line toward the boat. This made it easier to snag if laid on the bottom, or accidentally dropped.

Good luck!

diprna · 05-21-2012, 09:26 PM

Thank you all so much for taking the time to respond. My husband and I have learned so much already! We are feeling more confident giving the whips another shot (this time increasing to 20000 lb wt). Yesterday we bought and installed snubbers. Hopefully the new whips will do the trick. Maybe someday we will end up with a lift but we really would prefer not......the hassle of taking in and out and even storage (we have no flat land!) would be nice to avoid. Lastly, the water is too shallow at our dock so in order to use a lift, we would need to extend the dock....real snowball effect which hits the checkbook hard. Thanks again for all the great advice and comments. Joyce

diprna · 05-21-2012, 09:28 PM

We are planning to apply for the mooring permit. It would be nice to have the option on the really rough days.

Pricestavern · 05-22-2012, 07:24 AM

My wife and I want to purchase whips (sounds funny, right). Where to buy here at the lake?

Jonas Pilot · 05-22-2012, 09:01 AM

Wicked Wanda's Winnipesaukee Whips Wolfeboro.

LIforrelaxin · 05-22-2012, 03:36 PM

Quote:

Originally Posted by Pricestavern

My wife and I want to purchase whips (sounds funny, right). Where to buy here at the lake?

Many places can help you with whips....

I personally use Center Harbor dock and Pier....

you can also find them online at Overtons

and Last take a peak on craigs list... I fond Whips for my jetski there, for cheap money.

camp guy · 05-22-2012, 03:52 PM

Considering that fact that you are going to use these whip to secure a major asset in your life, don't buy used, and don't skimp on quality. I would suggest buying from a reputable, local dealer, and making sure that they are installed exactly according to directions, right down to the last nut! If you should experience problems, by buying locally and installing them correctly, you will have the best chance for a satisfactory resolution to your problems.

I bought whips locally, installed them according to the directions, and they worked well while I still had my boat.

DickR · 05-22-2012, 07:28 PM

Amen on the careful installation. Bear in mind that the downward pull by the boat at the end of the whip as it pitches in waves produces a tremendous torque at the point of attachment to the dock. You ought to check how the deck is attached to the frame, particularly on the opposite side of the dock from where the whip base is affixed, which must resist the torque of the whip. You may need some reinforcement at both sides of the dock. Even the side where the whip is affixed will see a fair amount of sideways torque, which happens when the attachment of the line to the boat is not straight out from where the whip base is on the dock, but toward the inner or outer end of the dock.

NoBozo · 05-22-2012, 07:59 PM

I LIKE the Kedge Anchor solution that was recommended earlier. A Kedge anchor is NOT A MOORING. It is a large (storm) Anchor..like a Danforth..or maybe a CQR placed out away from the boat to Windward..in the correct position..to be determined... by the conditions. Trial and Error. . It is an Anchor ...so you are not bound by any stinkin Mooring regulations.

The kedge will have Chain AND Nylon from the anchor up to the boat. Just like an anchor. Simple. DON'T YOU JUST HATE SIMPLE....??

NB

BTW: If you put a granite/cement "SINKER" out there...you GOT a Mooring

Rangervx · 05-22-2012, 09:43 PM

anyone thinking about whips...please research/contact Gordon at mooring products international....i would never trust my boat to any other product...these whips are top notch. to each his own however...

ApS · 05-23-2012, 05:07 AM

Quote:

Originally Posted by NoBozo

...A Kedge anchor is NOT A MOORING. It is a large (storm) Anchor...so you are not bound by any stinkin Mooring regulations..."

Even more sketches, pix, advice, "Sentinels", and "warps" here:

http://www.winnipesaukee.com/forums/...d.php?p=128557

Note for member musconnet—I have an update for you, but your inbox is full.

Kamper · 05-23-2012, 08:10 AM

Quote:

Originally Posted by NoBozo

... It is an Anchor ...so you are not bound by any stinkin Mooring regulations.
...

I would have agreed with you but in the incident I cited, the MP's point of view was that if you left it in the water when the boat left, it was a mooring.

FWIW - A block can be used as an anchor. A 'mooring' can utilise an anchor. It's a case of function not form.

Rattlesnake Guy · 05-25-2012, 09:26 PM

Like boats, all Whips are not created equal. The whips I often see at places around the lake are not very big. They can be expensive depending on size. You get what you pay for.

05-17-2012, 05:22 PM	#1
Misty Blue Senior Member Join Date: Jul 2004 Posts: 658 Thanks: 121 Thanked 283 Times in 98 Posts	Use a kedge. A way to deal with this is to use a kedgeing anchor. A kedge is an anchor (either a regular anchor or a mooring block) attached to the outboard side of the boat. Our set up... About 15 feet outboard of our boats we plant a mooring block. Attached to the block is about 6 feet of heavy chain. Attached to the chain is enough nylon (1/2 inch is good) line to reach a conveniant place on your dock. You tie up the boat to the dock in the regular way only a bit looser. You then take the kedging line and secure it to your outboard, midships cleat. With the loose dock lines the kedging line will pull the boat away from the dock. Adjust your docking lines so that the boat is about a foot from the rubbing posts. The weight of the chain running along the bottom will lift and drop as the boat moves up and down and will act as a shock absorber. It is cheap and easy on the boat and no permit required. Good luck! Misty Blue.

05-17-2012, 07:59 PM	#2
Rattlesnake Guy Senior Member Join Date: Sep 2004 Posts: 1,254 Thanks: 423 Thanked 366 Times in 175 Posts	We have used the same pair of over sized whips on the broads for 10 years. We have always used the collapsing triangle method as shown here. The triangle prevents the twisting force. Attached Images

05-18-2012, 09:45 AM	#6
Flyfisha Senior Member Join Date: Apr 2009 Location: Rattlesnake Island Posts: 140 Thanks: 58 Thanked 46 Times in 24 Posts	Whips Done it both ways--I have had oversize whips for about 15 years and have had good luck. My shore station sits on Rattlesnake looking for a new home. Sorry it's only rated for 3600# It really became a pain to take out and put in!

05-21-2012, 09:26 PM	#10
diprna Member Join Date: May 2012 Location: Meredith Bay/Bow Posts: 20 Thanks: 33 Thanked 2 Times in 2 Posts	Thank you! Thank you all so much for taking the time to respond. My husband and I have learned so much already! We are feeling more confident giving the whips another shot (this time increasing to 20000 lb wt). Yesterday we bought and installed snubbers. Hopefully the new whips will do the trick. Maybe someday we will end up with a lift but we really would prefer not......the hassle of taking in and out and even storage (we have no flat land!) would be nice to avoid. Lastly, the water is too shallow at our dock so in order to use a lift, we would need to extend the dock....real snowball effect which hits the checkbook hard. Thanks again for all the great advice and comments. Joyce

05-21-2012, 09:28 PM	#11
diprna Member Join Date: May 2012 Location: Meredith Bay/Bow Posts: 20 Thanks: 33 Thanked 2 Times in 2 Posts	Ps.... We are planning to apply for the mooring permit. It would be nice to have the option on the really rough days.

The Following 4 Users Say Thank You to Misty Blue For This Useful Post:
CTYankee (05-17-2012), diprna (05-20-2012), Jonas Pilot (05-17-2012), Winnisquamguy (05-18-2012)

The Following 2 Users Say Thank You to Rattlesnake Guy For This Useful Post:
diprna (05-20-2012), rgilfert (05-18-2012)

05-17-2012, 08:34 PM	#3
Jonas Pilot Senior Member Join Date: Apr 2005 Location: Wolfeboro, New Hampshire is my home, 24-7-365 Posts: 1,686 Thanks: 1,047 Thanked 336 Times in 189 Posts	Do you use bumpers too?

05-18-2012, 08:38 AM	#5
SAMIAM Senior Member Join Date: Apr 2004 Location: Moultonborough Posts: 2,924 Thanks: 350 Thanked 1,693 Times in 595 Posts	I've had great luck with mooring whips....secret is...go oversize for your boat or make sure they are heavy duty and they should handle most anything. Misty Blue has a good idea too. If you place a well anchored mooring ball for the bow, you can tie the stern to your dock and still have easy access to your boat. Not too difficult, just takes a little experimenting. Boat lifts are fine in salt water since you need to wash your boat and flush your engine after use but for fresh water, that's a lot of money to spend when there are lots of cheaper options. Good luck.

05-18-2012, 11:47 AM	#7
Rangervx Senior Member Join Date: Oct 2011 Location: VIRGINIA / WINTER HARBOR Posts: 82 Thanks: 28 Thanked 28 Times in 15 Posts	i would suggest contacting the folks at Mooring Products International. they are the inventors of the mooring whips and their whips are top notch. i would never trust my boat to anything other than these whips...period...end of story. they are out of florida...call them up and don't be suprised if you speak with the owner/president.

05-18-2012, 10:05 PM	#8
Rattlesnake Guy Senior Member Join Date: Sep 2004 Posts: 1,254 Thanks: 423 Thanked 366 Times in 175 Posts	RG has become an expert at tying lines to the dock post in a way that the lines do not wear from rubbing. Probably common to many on here but she wraps it so the line exist from between two other wraps and can't rub on the wood.

05-22-2012, 07:24 AM	#12
Pricestavern Senior Member Join Date: Oct 2006 Location: Valencia, Spain (formerly Rattlesnake Isle) Posts: 389 Thanks: 135 Thanked 142 Times in 82 Posts	Where to Purchase Whips? My wife and I want to purchase whips (sounds funny, right). Where to buy here at the lake?

05-22-2012, 09:01 AM	#13
Jonas Pilot Senior Member Join Date: Apr 2005 Location: Wolfeboro, New Hampshire is my home, 24-7-365 Posts: 1,686 Thanks: 1,047 Thanked 336 Times in 189 Posts	Wicked Wanda's Winnipesaukee Whips Wolfeboro.

05-22-2012, 03:52 PM	#15
camp guy Senior Member Join Date: Apr 2004 Location: formerly Winter Harbor, still Wolfeboro Posts: 1,204 Thanks: 308 Thanked 535 Times in 299 Posts	boat whips ... Considering that fact that you are going to use these whip to secure a major asset in your life, don't buy used, and don't skimp on quality. I would suggest buying from a reputable, local dealer, and making sure that they are installed exactly according to directions, right down to the last nut! If you should experience problems, by buying locally and installing them correctly, you will have the best chance for a satisfactory resolution to your problems. I bought whips locally, installed them according to the directions, and they worked well while I still had my boat.

05-22-2012, 07:28 PM	#16
DickR Senior Member Join Date: Apr 2008 Location: Moultonborough Posts: 758 Thanks: 4 Thanked 260 Times in 172 Posts	Amen on the careful installation. Bear in mind that the downward pull by the boat at the end of the whip as it pitches in waves produces a tremendous torque at the point of attachment to the dock. You ought to check how the deck is attached to the frame, particularly on the opposite side of the dock from where the whip base is affixed, which must resist the torque of the whip. You may need some reinforcement at both sides of the dock. Even the side where the whip is affixed will see a fair amount of sideways torque, which happens when the attachment of the line to the boat is not straight out from where the whip base is on the dock, but toward the inner or outer end of the dock.

05-22-2012, 07:59 PM	#17
NoBozo Senior Member Join Date: Jun 2008 Location: Portsmouth. RI Posts: 2,231 Thanks: 400 Thanked 460 Times in 308 Posts	I LIKE the Kedge Anchor solution that was recommended earlier. A Kedge anchor is NOT A MOORING. It is a large (storm) Anchor..like a Danforth..or maybe a CQR placed out away from the boat to Windward..in the correct position..to be determined... by the conditions. Trial and Error. . It is an Anchor ...so you are not bound by any stinkin Mooring regulations. The kedge will have Chain AND Nylon from the anchor up to the boat. Just like an anchor. Simple. DON'T YOU JUST HATE SIMPLE....?? NB BTW: If you put a granite/cement "SINKER" out there...you GOT a Mooring

05-22-2012, 09:43 PM	#18
Rangervx Senior Member Join Date: Oct 2011 Location: VIRGINIA / WINTER HARBOR Posts: 82 Thanks: 28 Thanked 28 Times in 15 Posts	anyone thinking about whips...please research/contact Gordon at mooring products international....i would never trust my boat to any other product...these whips are top notch. to each his own however...

05-25-2012, 09:26 PM	#21
Rattlesnake Guy Senior Member Join Date: Sep 2004 Posts: 1,254 Thanks: 423 Thanked 366 Times in 175 Posts	Like boats, all Whips are not created equal. The whips I often see at places around the lake are not very big. They can be expensive depending on size. You get what you pay for.