Parker Marine Slip Access?

fpartri497 · 09-11-2006, 06:23 AM

Quote:

Originally Posted by searay220

My friend this year couldn't get his boat out until the fourth of July week. Seems like a ton of money for a real short season nevermind the trouble with Parkers service dept. He is going to West Alton Marine next year.My 2cents.

Never once In eight years did I ever have a service Issue at parkers. They do a faboulus job. They serviced my boats every year. My only Issue Is with the bridge not them My new Azure requires 65 " so even the slighest high water and Im s-----d.

Twice this season I had to be fork lifted accross the street to downings so I could go out for the day. many times had to hand walk the boat under the bridge.

Joe Kerr · 09-11-2006, 08:27 AM

When you are talking about less than a few inches of needed clearance to get under the bridge I have a solution. I accidentally discovered that my boat would sit a few inches lower in the water when the bilge had a few inches of water. The bilge pump cleaned out the bilge in minutes and I got the leaky hose fixed.

If I needed an extra inch or two of bridge clearance I would consider pumping water into the boat before going under the bridge. In my boat there is nothing in the bilge that would be damaged by a few inches of water or sloshing water.

It's a similar principle to big trucks that need an inch to get under a bridge. They let air out of the tires until the truck is an inch lower.

I got to believe that someone slipped in back Bay or at Parker Marine has thought of this or tried this before. It's a little extra work but may be worth it.

codeman671 · 09-11-2006, 08:36 AM

I had to "walk" my pontoon under quite a few times due to high water. My tritoon sat rather high in the water and I would have to remove my bimini (even folded down it would rub) as well as my windshield.

I never used them for service but they seemed like decent people. Can't beat the price!

ThePlut · 09-11-2006, 09:11 AM

My dealer suggested the same thing, but quite frankly, I couldn't stomach the idea of intentionally filling my bilge with water and pumping it back out.

However, there are many ski boats which now incorporate water bag systems (ballast) into the bilge or ski locker. I would consider doing that, putting a water bag in the bilge or ski locker that has a separate pump to bring in and exhaust water to gain a few hundred lbs and a few inches of clearance.

Defintely could have done something like that as well.

Again, for me, at 57" spec, I was able to get in/out while there was still a no wake zone in effect, and was therefore minimally interested in doing so. Hopefully, this spring's rain is not a new pattern for the lake, for all of our sake. Also, in talking with the dealer, the 57" number was the absolute highest spec (lightest boat, no fuel, etc...). I'm sure the boat itself sits a few inches lower than that under normal operating conditions.

Parker was upfront with me, that if I had a spec of greater than 60", I might have some trouble...

chipj29 · 09-11-2006, 09:47 AM

Wow, that video is amazing...that is Tight! With a capital T! One wave and you are in deep doo-doo!

ThePlut · 09-11-2006, 10:50 AM

It was only once or twice I had to do that, and I think the lake reading was 6 or so inches higher than "full lake" from the NH-DES charts.

Stinger · 09-11-2006, 11:39 AM

Yeah, that video looks familiar, I actually got a ~1/64" knick on the top of my windshield frame from my first trip under after the rains this year, lake level at the time was was 505.32, my boat's bridge clearance is 43", according to Bizer Map I'd break glass. Parker's said the "real" bridge clearance is more like 5.5 ft, they ought to know. Bizer is probably (rightfully) conservative in their measurement on their map.

The Service at Parkers has been excellent everytime I have used them (this is my 7th season). They pay attention to detail and do the extra things like grease the trailer wheel bearings when they winterize my boat. Earlier this year I needed a jump start at my slip, I called the office, they sent a mechanic out within 10 minutes, jump start done, no charge (pun intended).

sgold44 · 09-11-2006, 06:56 PM

This is my first year at Parker, & I have had nothing but great experiences with them. I started the season w/a 22 ft bowrider, & from mid june was able to cruise under the bridge. The first week of August I bought a new boat that's 24 ft, & I did scratch the windshield frame once. I've used Parkers for service twice, & they fixed me up quickly & well. I would recommend them highly.

gtxrider · 09-11-2006, 08:12 PM

There are several options to get under the bridge.

1. Lower the lake (know any one at the dam?)

2. Raise the bridge (not likely)

3. Go real fast and duck.

4. Take everyone you know out for a boat ride at the same time.

4. Do like the truckers do and air down the tires. (let some water into the bilge)

But than how often does the lake get as high as it was this year?

fpartri497 · 09-11-2006, 09:48 PM

Quote:

Originally Posted by chipj29

Wow, that video is amazing...that is Tight! With a capital T! One wave and you are in deep doo-doo!

I had to handwalk my boat under the bridge many times with all the parker boys In the bow for ballast.

Alton Bay Resident · 09-12-2006, 12:37 PM

Take a look at the average lake height for the past few years including this and you'll see that even with 60" bridge height up to the 1st or 2nd week in July is not good. Nevermind they seem to be keeping the lake higher now that DES controls the lake level...

fpartri497 · 09-13-2006, 09:29 AM

Quote:

Originally Posted by Alton Bay Resident

Take a look at the average lake height for the past few years including this and you'll see that even with 60" bridge height up to the 1st or 2nd week in July is not good. Nevermind they seem to be keeping the lake higher now that DES controls the lake level...

How and when did the DES take over control of the dam?

09-11-2006, 08:27 AM	#2
Joe Kerr Senior Member Join Date: Apr 2004 Location: Massachusetts Posts: 92 Thanks: 23 Thanked 16 Times in 5 Posts	Get extra clearance When you are talking about less than a few inches of needed clearance to get under the bridge I have a solution. I accidentally discovered that my boat would sit a few inches lower in the water when the bilge had a few inches of water. The bilge pump cleaned out the bilge in minutes and I got the leaky hose fixed. If I needed an extra inch or two of bridge clearance I would consider pumping water into the boat before going under the bridge. In my boat there is nothing in the bilge that would be damaged by a few inches of water or sloshing water. It's a similar principle to big trucks that need an inch to get under a bridge. They let air out of the tires until the truck is an inch lower. I got to believe that someone slipped in back Bay or at Parker Marine has thought of this or tried this before. It's a little extra work but may be worth it. __________________ ~ Joe Kerr

09-11-2006, 09:11 AM	#4
ThePlut Senior Member Join Date: Jul 2005 Posts: 150 Thanks: 1 Thanked 13 Times in 11 Posts	Hooo boy My dealer suggested the same thing, but quite frankly, I couldn't stomach the idea of intentionally filling my bilge with water and pumping it back out. However, there are many ski boats which now incorporate water bag systems (ballast) into the bilge or ski locker. I would consider doing that, putting a water bag in the bilge or ski locker that has a separate pump to bring in and exhaust water to gain a few hundred lbs and a few inches of clearance. Defintely could have done something like that as well. Again, for me, at 57" spec, I was able to get in/out while there was still a no wake zone in effect, and was therefore minimally interested in doing so. Hopefully, this spring's rain is not a new pattern for the lake, for all of our sake. Also, in talking with the dealer, the 57" number was the absolute highest spec (lightest boat, no fuel, etc...). I'm sure the boat itself sits a few inches lower than that under normal operating conditions. Parker was upfront with me, that if I had a spec of greater than 60", I might have some trouble...

09-11-2006, 09:47 AM	#5
chipj29 Senior Member Join Date: Apr 2004 Location: Bow Posts: 1,874 Thanks: 521 Thanked 308 Times in 162 Posts	Wow! Wow, that video is amazing...that is Tight! With a capital T! One wave and you are in deep doo-doo!

09-11-2006, 10:50 AM	#6
ThePlut Senior Member Join Date: Jul 2005 Posts: 150 Thanks: 1 Thanked 13 Times in 11 Posts	Yup It was only once or twice I had to do that, and I think the lake reading was 6 or so inches higher than "full lake" from the NH-DES charts.

09-11-2006, 11:39 AM	#7
Stinger Member Join Date: Apr 2004 Location: Dover, NH & Parker Marine Posts: 30 Thanks: 0 Thanked 1 Time in 1 Post	Parker Marine Bridge Yeah, that video looks familiar, I actually got a ~1/64" knick on the top of my windshield frame from my first trip under after the rains this year, lake level at the time was was 505.32, my boat's bridge clearance is 43", according to Bizer Map I'd break glass. Parker's said the "real" bridge clearance is more like 5.5 ft, they ought to know. Bizer is probably (rightfully) conservative in their measurement on their map. The Service at Parkers has been excellent everytime I have used them (this is my 7th season). They pay attention to detail and do the extra things like grease the trailer wheel bearings when they winterize my boat. Earlier this year I needed a jump start at my slip, I called the office, they sent a mechanic out within 10 minutes, jump start done, no charge (pun intended).

09-11-2006, 08:36 AM	#3
codeman671 Senior Member Join Date: Jan 2005 Posts: 3,498 Thanks: 221 Thanked 812 Times in 488 Posts	I had to "walk" my pontoon under quite a few times due to high water. My tritoon sat rather high in the water and I would have to remove my bimini (even folded down it would rub) as well as my windshield. I never used them for service but they seemed like decent people. Can't beat the price!

09-11-2006, 06:56 PM	#8
sgold44 Member Join Date: May 2006 Location: Middleton, MA & Paugus Bay Posts: 46 Thanks: 0 Thanked 1 Time in 1 Post	xcellent service This is my first year at Parker, & I have had nothing but great experiences with them. I started the season w/a 22 ft bowrider, & from mid june was able to cruise under the bridge. The first week of August I bought a new boat that's 24 ft, & I did scratch the windshield frame once. I've used Parkers for service twice, & they fixed me up quickly & well. I would recommend them highly.

09-11-2006, 08:12 PM	#9
gtxrider Senior Member Join Date: Mar 2004 Location: Piscataway, NJ Posts: 1,030 Thanks: 2 Thanked 46 Times in 24 Posts	Options! There are several options to get under the bridge. 1. Lower the lake (know any one at the dam?) 2. Raise the bridge (not likely) 3. Go real fast and duck. 4. Take everyone you know out for a boat ride at the same time. 4. Do like the truckers do and air down the tires. (let some water into the bilge) But than how often does the lake get as high as it was this year?

09-12-2006, 12:37 PM	#11
Alton Bay Resident Member Join Date: Apr 2004 Posts: 23 Thanks: 0 Thanked 8 Times in 1 Post	60" is slim for the last few years Take a look at the average lake height for the past few years including this and you'll see that even with 60" bridge height up to the 1st or 2nd week in July is not good. Nevermind they seem to be keeping the lake higher now that DES controls the lake level...