Running on Generator

MeredithMan · 12-23-2022, 08:09 AM

....Lost power here in Bedford about 6:30 this morning, and running off the generator right now as I write this. We have underground power in this neighborhood, so I guess one of the feeder lines went down. Odd, though, because even though it's windy, it's not that windy here....

WinnisquamZ · 12-23-2022, 06:06 PM

Went out and did some errands around noon and became aware of the power outage in the weirs. My lights have been blinking must of the day, just lost power. Good lord willing we are out of here at 10am tomorrow morning. Unsure if I need to drag the generator out. On the plus side, wrapping presents by candle light. Most of the cooking is done.

Sent from my iPhone using Winnipesaukee Forum mobile app

ishoot308 · 12-23-2022, 06:11 PM

I have been on generator power since 2:00 PM this afternoon here in Gilford…

Dan

WinnisquamZ · 12-23-2022, 06:17 PM

Quote:

Originally Posted by MeredithMan

....Lost power here in Bedford about 6:30 this morning, and running off the generator right now as I write this. We have underground power in this neighborhood, so I guess one of the feeder lines went down. Odd, though, because even though it's windy, it's not that windy here....

My daughter in Bedford just lost her power about 20 minutes ago. Hers are also underground

Sent from my iPhone using Winnipesaukee Forum mobile app

fatlazyless · 12-24-2022, 09:02 AM

Looks like the BearCam .... www.bearchow.com ..... has done gone black ...... must have lost island power, or some-ting?

And, where's all the deep snow? My place is about two miles south, and I was raking the leaves off the ground on Thursday, Dec 22. Made what was probably the last dump run with a trailer load of dry oak leafs till next spring. Me-thinks the remaining leaves will be frozen in place until late March/early April but you never know.

BroadHopper · 12-24-2022, 09:12 AM

Wildwood Village utilities are underground. Two different feeders. One off Lexington Drive and the other off Lynnewood. Both have separate power feeds. Been lucky in the past 2 decades.

8gv · 12-24-2022, 09:35 AM

All day yesterday and last night we had up and down power failures here in Laconia off Parade Rd.

They were never long enough to require the generator but I proactively flipped the breakers on a few items that have fancy electronics in them.

There was a weird occurrence as well.

At one point about half of our stuff quit but all else was working.

I figured it was due to the loss of one leg of the incoming power and that the outage items were on that leg in the breaker panel.

We contacted Eversource but they said there were no know outages in my area.

Down the street there was a crew working on a power poll that was snapped in half so I figured it was work in progress.

But a quick glance at the panel revealed that all of the breakers with white buttons were tripped.

I reset them and we were back in action.

My experience with this type of breaker is that they are a ground fault interrupter.

Maybe the up and down or the power crew's work tripped them.

I was also wondering if they were arc fault breakers.

The house was built in 2010 and I do not know if arc faults were required then.

Do they have a button or do they just trip like a traditional breaker?

ITD · 12-24-2022, 09:47 AM

Power out since 6pm last night over here in Moultonborough on the Center Harbor line. No idea when it will be restored. Just got my generator running last Friday. Working great so far.

Slickcraft · 12-24-2022, 10:42 AM

We were at Shaw's in Gilford about 9:45 am today and they were running on generator. While the store was fully open for business, the lighting was a bare minimum and the heat was off. We had winter coats on and were fine but the staff were a bit cold.

Alan

ishoot308 · 12-24-2022, 10:51 AM

Still on Genny power here in Gilford…going on 21 straight hours now…

Merry Christmas everyone!

Dan

thinkxingu · 12-24-2022, 11:09 AM

Quote:

Originally Posted by ishoot308

Still on Genny power here in Gilford…going on 21 straight hours now…

Merry Christmas everyone!

Dan

What's your genny's power source, propane or NG? I'm wondering how long you can be disconnected before running out of fuel.

Sent from my SM-G990U1 using Tapatalk

ishoot308 · 12-24-2022, 01:00 PM

Quote:

Originally Posted by thinkxingu

What's your genny's power source, propane or NG? I'm wondering how long you can be disconnected before running out of fuel.

Sent from my SM-G990U1 using Tapatalk

Propane…I have a 500 gallon tank. I believe my 20 KW generator uses around 3 gallons per hour or 72 gallons a day.

Merry Christmas Think!

Dan

Descant · 12-24-2022, 01:05 PM

Quote:

Originally Posted by thinkxingu

What's your genny's power source, propane or NG? I'm wondering how long you can be disconnected before running out of fuel.

We didn't lose power this time around (fingers crossed).

Pine Island Guy · 12-24-2022, 01:16 PM

Still running on generator here on Pine Island, walked the power lines and one spur line to a house is down, but other than that everything looks to be intact. It looked like from the NHEC outage map that quite a bit of Meredith Neck is out and hoping that when that is fixed the island will come back on-line!

Heading back to the mainland tonight, lots of skim ice near the shores and since I'm bringing the cocktails to the Christmas party tomorrow, I'd hate to be iced in on the island and have to drink it all myself hahaha

Merry Christmas, Happy Hannukah, Fabulous Festivus, and all the other holidays - PIG

thinkxingu · 12-24-2022, 01:25 PM

Quote:

Originally Posted by ishoot308

Propane…I have a 500 gallon tank. I believe my 20 KW generator uses around 3 gallons per hour or 72 gallons a day.

Merry Christmas Think!

Dan

Fingers crossed you get power back before the 7th day!

Merry Christmas to you and yours, Dan—and Tuck says hi!

Sent from my SM-G990U1 using Tapatalk

thinkxingu · 12-24-2022, 01:27 PM

Quote:

Originally Posted by Descant

We didn't lose power this time around (fingers crossed).

We didn't, either, which is weird given how many around us did.

When we moved into town, we'd lose power if a mouse farted, but since ~2016 it's been much more reliable. Probably around the time Eversource took down a ton of roadside trees.

Sent from my SM-G990U1 using Tapatalk

ITD · 12-24-2022, 02:16 PM

I'm doing the 25 hour, 1st oil change around 7 tonight. Will probably be brisk out there.

codeman671 · 12-24-2022, 02:30 PM

Quote:

Originally Posted by thinkxingu

Fingers crossed you get power back before the 7th day!

Merry Christmas to you and yours, Dan—and Tuck says hi!

Sent from my SM-G990U1 using Tapatalk

Ours went down around 5pm last night and just came back on.
Hopefully you too since you aren’t that far from us.

ishoot308 · 12-24-2022, 02:42 PM

Quote:

Originally Posted by codeman671

Ours went down around 5pm last night and just came back on.
Hopefully you too since you aren’t that far from us.

Ours just came back after 24 1/2 hours down!

Thank you Eversource for working Christmas Eve to restore power!

Dan

thinkxingu · 12-24-2022, 03:31 PM

Bravo!

I hope the rest of y'all come back up soon!

Sent from my SM-G990U1 using Tapatalk

chachee52 · 12-25-2022, 04:55 PM

Quote:

Originally Posted by codeman671

Ours went down around 5pm last night and just came back on.
Hopefully you too since you aren’t that far from us.

LSP was the same. Ran up yesterday noon with a small generator to get the sump pump working on the 9" of water in the basement. Maybe now my dad will put a backup battery on it? It was about 20 years before we lost power for more than 2 hours, now it's happened a few times in the last 3-4 years.
Everyone was safe and that's what counts.

WinnisquamZ · 12-25-2022, 04:56 PM

Just got ours back after 52 hours. Shut the generator off and the house was 70 degrees. Left to visit the grandchildren. 28 hours later we got the power back and the house was 51 degrees. That’s a positive after all the work we did last winter. Wood stove is now going and the clocks are all reset. Fingers crossed we go another 8 years before the next multi day loss of power

Sent from my iPhone using Winnipesaukee Forum mobile app

ITD · 12-25-2022, 05:12 PM

Got mine back around 930 today. The generator ran for 35 hours. I estimate about 40 gallons of propane burned, but that could be off.

Kamper · 12-26-2022, 09:22 AM

Two trees came down about 5pm Friday night, about 1/2 mile from me. We had to go out so decided to just bundle up for the night, when we got back.

For the first time since I got it in 2010, my big genny wouldn't start even though it seemed ok on my pre-season equipment check. The apparent problem was no spark. I decided to not take time for it now and made a dash for Harbor Freight and got there at 925am Saturday. All they had left were 2000w inverter portables.

Since I was told my new furnace should only use clean power, I blessed my luck (and stifled my disappointment they wouldn't sell me one of the bigger floor models). The only issue was the diagram and instructions aren't quite right on where the oil plug is. If you get one, it's on the opposite side from the pull start.

The unit started right up and after the house was hot, I switched the line from the furnace (transfer switch) to my two refrigerators using a tap (heavy duty cords and tap).

I am happy with this item and may not bother to get a bigger unit even if I can't fix my old Chicago unit.

Many thanks to Clean Harbor for hazmat cleanup from the transformer that was involved and the line crews that got my lights on around midnight.

chachee52 · 12-26-2022, 06:16 PM

Quote:

Originally Posted by Kamper

Two trees came down about 5pm Friday night, about 1/2 mile from me. We had to go out so decided to just bundle up for the night, when we got back.

For the first time since I got it in 2010, my big genny wouldn't start even though it seemed ok on my pre-season equipment check. The apparent problem was no spark. I decided to not take time for it now and made a dash for Harbor Freight and got there at 925am Saturday. All they had left were 2000w inverter portables.

Since I was told my new furnace should only use clean power, I blessed my luck (and stifled my disappointment they wouldn't sell me one of the bigger floor models). The only issue was the diagram and instructions aren't quite right on where the oil plug is. If you get one, it's on the opposite side from the pull start.

The unit started right up and after the house was hot, I switched the line from the furnace (transfer switch) to my two refrigerators using a tap (heavy duty cords and tap).

I am happy with this item and may not bother to get a bigger unit even if I can't fix my old Chicago unit.

Many thanks to Clean Harbor for hazmat cleanup from the transformer that was involved and the line crews that got my lights on around midnight.

When I first bought my house, lost my power for over a week for 3 years in a row. My brother in law had the Honda 2000 portable. We ran the hot air furnace and the frig together without any issue. All depends on how big of a furnace of course. But worth looking into the specs of both to see if you could run both at the same time.

Kamper · 12-27-2022, 08:57 AM

Quote:

Originally Posted by chachee52

... worth looking into the specs of both to see if you could run both at the same time.

Thanks for the suggestion and comparison. I have 2 full size fridges (1 dumb and 1 'smart') and a bar fridge. I may try the furnace and smart fridge together because my wife is addicted to crushed ice with Pepsi, and tag team the furnace with the dumb fridge. The bar fridge can be left alone since we seldom put anything perishable in it.

tummyman · 12-27-2022, 10:35 AM

We run our boiler, fridge, power strip for battery recharge as well as cell phones, plus a nice LED light on the kitchen island and one on the second floor, all with our Honda 2000 ! Works perfect. Have a male receptacle on the outside of the house that i plug the generator feed into, then this feed goes to a double wall receptacle. Does everything we need except well pump that is 220. In the late fall, we leave three 5 gallon pails filled with water in our bathtub for flushing should the lake be frozen. Love my Honda...runs terrific with nice clean power and uses little gas. Did a little creative wiring in my boiler room and now it takes me 10 seconds to convert from house power to generator power. When power comes back, it again only take 10 seconds to remove the generator feed and go back to house power. Used to open up wire boxes and splice into a extension cord...not practical.

12-23-2022, 08:09 AM	#1
MeredithMan Senior Member Join Date: Aug 2013 Location: Bedford, NH; Meredith, NH Posts: 946 Thanks: 262 Thanked 812 Times in 331 Posts	Running on Generator ....Lost power here in Bedford about 6:30 this morning, and running off the generator right now as I write this. We have underground power in this neighborhood, so I guess one of the feeder lines went down. Odd, though, because even though it's windy, it's not that windy here....

12-23-2022, 06:11 PM	#3
ishoot308 Senior Member Join Date: Feb 2008 Location: Gilford, NH / Welch Island Posts: 6,232 Thanks: 2,384 Thanked 5,276 Times in 2,050 Posts	Generator I have been on generator power since 2:00 PM this afternoon here in Gilford… Dan __________________ It's Always Sunny On Welch Island!!

12-24-2022, 09:12 AM	#6
BroadHopper Senior Member Join Date: Oct 2004 Location: Laconia NH Posts: 5,570 Thanks: 3,205 Thanked 1,101 Times in 793 Posts	Two feeder lines. Wildwood Village utilities are underground. Two different feeders. One off Lexington Drive and the other off Lynnewood. Both have separate power feeds. Been lucky in the past 2 decades. __________________ Someday may never be an actual day.

12-24-2022, 10:51 AM	#10
ishoot308 Senior Member Join Date: Feb 2008 Location: Gilford, NH / Welch Island Posts: 6,232 Thanks: 2,384 Thanked 5,276 Times in 2,050 Posts	Still on Genny power here in Gilford…going on 21 straight hours now… Merry Christmas everyone! Dan __________________ It's Always Sunny On Welch Island!!

12-24-2022, 01:16 PM	#14
Pine Island Guy Senior Member Join Date: Jul 2004 Location: pine island of course! Posts: 406 Thanks: 244 Thanked 246 Times in 112 Posts	Pine Island out Still running on generator here on Pine Island, walked the power lines and one spur line to a house is down, but other than that everything looks to be intact. It looked like from the NHEC outage map that quite a bit of Meredith Neck is out and hoping that when that is fixed the island will come back on-line! Heading back to the mainland tonight, lots of skim ice near the shores and since I'm bringing the cocktails to the Christmas party tomorrow, I'd hate to be iced in on the island and have to drink it all myself hahaha Merry Christmas, Happy Hannukah, Fabulous Festivus, and all the other holidays - PIG

12-23-2022, 06:06 PM	#2
WinnisquamZ Senior Member Join Date: Dec 2016 Posts: 2,048 Thanks: 210 Thanked 652 Times in 435 Posts	Went out and did some errands around noon and became aware of the power outage in the weirs. My lights have been blinking must of the day, just lost power. Good lord willing we are out of here at 10am tomorrow morning. Unsure if I need to drag the generator out. On the plus side, wrapping presents by candle light. Most of the cooking is done. Sent from my iPhone using Winnipesaukee Forum mobile app

12-24-2022, 09:02 AM	#5
fatlazyless Senior Member Join Date: Apr 2004 Posts: 8,738 Blog Entries: 1 Thanks: 300 Thanked 1,007 Times in 735 Posts	Looks like the BearCam .... www.bearchow.com ..... has done gone black ...... must have lost island power, or some-ting? And, where's all the deep snow? My place is about two miles south, and I was raking the leaves off the ground on Thursday, Dec 22. Made what was probably the last dump run with a trailer load of dry oak leafs till next spring. Me-thinks the remaining leaves will be frozen in place until late March/early April but you never know.

The Following User Says Thank You to fatlazyless For This Useful Post:
Newbiesaukee (12-24-2022)

12-24-2022, 09:35 AM	#7
8gv Senior Member Join Date: Jan 2012 Posts: 2,092 Thanks: 64 Thanked 744 Times in 478 Posts	All day yesterday and last night we had up and down power failures here in Laconia off Parade Rd. They were never long enough to require the generator but I proactively flipped the breakers on a few items that have fancy electronics in them. There was a weird occurrence as well. At one point about half of our stuff quit but all else was working. I figured it was due to the loss of one leg of the incoming power and that the outage items were on that leg in the breaker panel. We contacted Eversource but they said there were no know outages in my area. Down the street there was a crew working on a power poll that was snapped in half so I figured it was work in progress. But a quick glance at the panel revealed that all of the breakers with white buttons were tripped. I reset them and we were back in action. My experience with this type of breaker is that they are a ground fault interrupter. Maybe the up and down or the power crew's work tripped them. I was also wondering if they were arc fault breakers. The house was built in 2010 and I do not know if arc faults were required then. Do they have a button or do they just trip like a traditional breaker?

12-24-2022, 09:47 AM	#8
ITD Senior Member Join Date: Apr 2004 Location: Moultonboro, NH Posts: 2,925 Thanks: 476 Thanked 691 Times in 387 Posts	Power out since 6pm last night over here in Moultonborough on the Center Harbor line. No idea when it will be restored. Just got my generator running last Friday. Working great so far.

12-24-2022, 10:42 AM	#9
Slickcraft Senior Member Join Date: Mar 2008 Location: Welch Island and The Taylor Community Posts: 3,296 Thanks: 1,222 Thanked 2,080 Times in 952 Posts	We were at Shaw's in Gilford about 9:45 am today and they were running on generator. While the store was fully open for business, the lighting was a bare minimum and the heat was off. We had winter coats on and were fine but the staff were a bit cold. Alan

12-24-2022, 02:16 PM	#17
ITD Senior Member Join Date: Apr 2004 Location: Moultonboro, NH Posts: 2,925 Thanks: 476 Thanked 691 Times in 387 Posts	I'm doing the 25 hour, 1st oil change around 7 tonight. Will probably be brisk out there.

12-24-2022, 03:31 PM	#20
thinkxingu Senior Member Join Date: Jul 2014 Posts: 6,212 Thanks: 1,167 Thanked 2,048 Times in 1,271 Posts	Bravo! I hope the rest of y'all come back up soon! Sent from my SM-G990U1 using Tapatalk

12-25-2022, 04:56 PM	#22
WinnisquamZ Senior Member Join Date: Dec 2016 Posts: 2,048 Thanks: 210 Thanked 652 Times in 435 Posts	Just got ours back after 52 hours. Shut the generator off and the house was 70 degrees. Left to visit the grandchildren. 28 hours later we got the power back and the house was 51 degrees. That’s a positive after all the work we did last winter. Wood stove is now going and the clocks are all reset. Fingers crossed we go another 8 years before the next multi day loss of power Sent from my iPhone using Winnipesaukee Forum mobile app

12-25-2022, 05:12 PM	#23
ITD Senior Member Join Date: Apr 2004 Location: Moultonboro, NH Posts: 2,925 Thanks: 476 Thanked 691 Times in 387 Posts	Got mine back around 930 today. The generator ran for 35 hours. I estimate about 40 gallons of propane burned, but that could be off.

12-26-2022, 09:22 AM	#24
Kamper Senior Member Join Date: Jul 2005 Location: Thornton's Ferry Posts: 1,302 Thanks: 67 Thanked 171 Times in 127 Posts	Two trees came down about 5pm Friday night, about 1/2 mile from me. We had to go out so decided to just bundle up for the night, when we got back. For the first time since I got it in 2010, my big genny wouldn't start even though it seemed ok on my pre-season equipment check. The apparent problem was no spark. I decided to not take time for it now and made a dash for Harbor Freight and got there at 925am Saturday. All they had left were 2000w inverter portables. Since I was told my new furnace should only use clean power, I blessed my luck (and stifled my disappointment they wouldn't sell me one of the bigger floor models). The only issue was the diagram and instructions aren't quite right on where the oil plug is. If you get one, it's on the opposite side from the pull start. The unit started right up and after the house was hot, I switched the line from the furnace (transfer switch) to my two refrigerators using a tap (heavy duty cords and tap). I am happy with this item and may not bother to get a bigger unit even if I can't fix my old Chicago unit. Many thanks to Clean Harbor for hazmat cleanup from the transformer that was involved and the line crews that got my lights on around midnight.

12-27-2022, 10:35 AM	#27
tummyman Senior Member Join Date: Aug 2009 Location: Moultonborough Posts: 832 Thanks: 256 Thanked 671 Times in 242 Posts	We run our boiler, fridge, power strip for battery recharge as well as cell phones, plus a nice LED light on the kitchen island and one on the second floor, all with our Honda 2000 ! Works perfect. Have a male receptacle on the outside of the house that i plug the generator feed into, then this feed goes to a double wall receptacle. Does everything we need except well pump that is 220. In the late fall, we leave three 5 gallon pails filled with water in our bathtub for flushing should the lake be frozen. Love my Honda...runs terrific with nice clean power and uses little gas. Did a little creative wiring in my boiler room and now it takes me 10 seconds to convert from house power to generator power. When power comes back, it again only take 10 seconds to remove the generator feed and go back to house power. Used to open up wire boxes and splice into a extension cord...not practical.