Faucet issue... Help !

bigdog · 08-06-2014, 05:58 PM

Have a issue with a kitchen faucet.
It's a Delta faucet....

I am replacing the tiny springs and rubber bushings under each faucet handle.
I've replaced one already but having an issue removing the handle from the other.

The handle (L type handel) is held to the post by a 'tiny' Allen screw. I am using correct allen wrentch, but the screw appears to be mostly stripped in the handle hole from a previous replacement I suspect? The screw is located under handle L without much clearance, just enough for me to place the allen wrentch.

About the screw possibly being stripped or partially stripped.....
Any suggestions on how to remove? I'm at a loss at this point.

Thanks for any suggestions !

Bigdog

JDeere · 08-06-2014, 06:08 PM

Call delta. They have great support!

Rusty · 08-06-2014, 07:03 PM

The hex where the wrench goes is probably stripped. Try a small flat bladed screwdriver. Sometimes you can catch the corners of the hex with the tip of the screwdriver.

Resident 2B · 08-06-2014, 10:10 PM

If what Rusty suggested does not work, You may need to remove the whole faucet from the sink to get better access. If the hex socket is stripped, the only think that will work is to carefully drill it out. Be careful not to remove the threads. just use a drill that is slightly smaller than the internal diameter of the threaded hole. Hopefully, Rusty's trick will do the job as it is a simple solution.

Good luck!

R2B

SIKSUKR · 08-07-2014, 08:06 AM

Go to Home Depot or your local hardware store and buy one of these.There are different types but here is one.

Broken Glass · 08-07-2014, 10:05 AM

Try filing down the top of the Allen wrench. This will square off the profile of the wrench, and the bite will be optimized. Use as much pressure as you are able when you press the wrench on to the set screw. This is your last shot before getting out the drill.....

08-06-2014, 05:58 PM	#1
bigdog Senior Member Join Date: Apr 2006 Location: Central MA-Gilford Posts: 1,453 Thanks: 347 Thanked 124 Times in 98 Posts	Faucet issue... Help ! Have a issue with a kitchen faucet. It's a Delta faucet.... I am replacing the tiny springs and rubber bushings under each faucet handle. I've replaced one already but having an issue removing the handle from the other. The handle (L type handel) is held to the post by a 'tiny' Allen screw. I am using correct allen wrentch, but the screw appears to be mostly stripped in the handle hole from a previous replacement I suspect? The screw is located under handle L without much clearance, just enough for me to place the allen wrentch. About the screw possibly being stripped or partially stripped..... Any suggestions on how to remove? I'm at a loss at this point. Thanks for any suggestions ! Bigdog

08-06-2014, 07:03 PM	#3
Rusty Senior Member Join Date: Oct 2010 Posts: 2,028 Thanks: 603 Thanked 687 Times in 425 Posts	The hex where the wrench goes is probably stripped. Try a small flat bladed screwdriver. Sometimes you can catch the corners of the hex with the tip of the screwdriver. __________________ It's never crowded along the extra mile.

08-07-2014, 08:06 AM	#5
SIKSUKR Senior Member Join Date: Apr 2004 Posts: 5,075 Thanks: 215 Thanked 903 Times in 509 Posts	Screw extractor or ez out Go to Home Depot or your local hardware store and buy one of these.There are different types but here is one. Attached Images __________________ SIKSUKR

08-07-2014, 10:05 AM	#6
Broken Glass Senior Member Join Date: Jun 2008 Location: Atkinson,NH/Rattlesnake Island Posts: 164 Thanks: 332 Thanked 67 Times in 28 Posts	Allen Wrench Try filing down the top of the Allen wrench. This will square off the profile of the wrench, and the bite will be optimized. Use as much pressure as you are able when you press the wrench on to the set screw. This is your last shot before getting out the drill.....

The Following User Says Thank You to bigdog For This Useful Post:
Not to Worry (08-07-2014)

08-06-2014, 06:08 PM	#2
JDeere Senior Member Join Date: Apr 2004 Posts: 295 Thanks: 74 Thanked 52 Times in 25 Posts	Call delta. They have great support!

08-06-2014, 10:10 PM	#4
Resident 2B Senior Member Join Date: Apr 2004 Location: North Shore, MA Posts: 1,358 Thanks: 996 Thanked 314 Times in 164 Posts	If what Rusty suggested does not work, You may need to remove the whole faucet from the sink to get better access. If the hex socket is stripped, the only think that will work is to carefully drill it out. Be careful not to remove the threads. just use a drill that is slightly smaller than the internal diameter of the threaded hole. Hopefully, Rusty's trick will do the job as it is a simple solution. Good luck! R2B